• <u id="cioag"></u>
  • Track Rollers Bearings|Changzhou Enke Bearing Co.,Ltd

    ABOUT US||QUAILTY||PRODUCTS||SALES NETWORK||SERVICE||CONTACT US||HOMEPAGE
    Products

    Contact Us:
    Changzhou Enke Bearing Co.,ltd
    Address: High and New District, WuJin,ChangZhou City,P.R.China
    TEL : 0086-519-86277691
    M:(0)13337890691
    FAX : 0086-519-86581167
    E-mail : hygou@hotmail.com


                Track Rollers Bearings

    PRODUCT

    RSTO RSTO..X
    RNA22..2RS
    NATR..PP NATV..PP
    NUTR
    CRY...V,CRY...VUU

    KR..PP KRV..PP KRE..PP KRVE..PP NUKR NUKRE
    CR...R,CR,CR...UUR,CR...UU

    yoke type track rollers with thick wall outer ring can roll directly on the tray under heavy load. It includes pressure roller,eccentric roller,rocking arm roller.The roller diameter is of ball shape or cylinder ball shape.With the ball shape,the inclining position resulted during the fitting can be compensated.

    Structure
    RSTO
    No retaining edge in outer ring,yoke type track rollers without inner ring

    STO
    No retaining edge in outer ring,yoke type track rollers with inner ring

    RNA22- 2RS
    Double face sealed, yoke type track rollers without inner ring

    NA22 - 2RS
    Double face sealed, yoke type track rollers with inner ring

    NATR
    NATR - PP
    Plain retaining ring,axial guiding, yoke type track rollers

    NATV
    NATV - PP
    Plain retaining ring,axial guiding, yoke type track rollers
    Full complement needle roller type

    NUTR
    Rolling body guiding,yoke type track rollers,full roller type

    CRY
    Inch system,plain retaining ring,axial guiding, yoke type track rollers

    RSTO and STO type yoke type track rollers

    ENKE series yoke type track rollers RSTO type,without inner ring,can directly run on the quenched shaft.STO type has inner rings,its inner ring,outer ring and the combinative needle roller retainer assembly can be fitted separately.Because RSTO and STO type yoke type track rollers have no retaining edges and the end retaining rings,axial guiding is needed in fitting.the guiding surface must be precisely machined at least.


    RNA22...2RS,NA22...2RS type yoke type track rollers

    The diameter of such rollers is the same as STO series rollers but a little wider.Its double face sealed structure ensures no maintenance requested.The operational temperature range is -20??£-120??.When fitting the yoke type track rollers without inner rings (RNA22...2RS)series,noice no damage to the sealing rings should occur.The outer ring needs end face guidance.


    NATR and NATR...PP type yoke type track rollers

    NATR series roller contains outer ring,inner ring,needle retainer assembly and the retaining rings which are pressed and fixed by the two sides of inner ring.NATR...PP series has an additional sealing ring.This kind of yoke type track rollers have huge lubricant storage space,so they can be used for long period without re-grease.


    NATV and NATV...PP type yoke type track rollers

    NATV series yoke type track roller is basically the same as NATR series.The only difference is that NATV is full complement needle roller type.Therefore it can sustain heavier load under low speed.Frequent lubricating should be noticed.NATV...PP is a series with sealing ring structure.


    NUTR type yoke type track rollers

    NUTR series yoke type track roller is double row full roller bearing with retaining edge guiding outer ring.All the parts of the bearing are pressed into the sealing cage of outer ring forming a complete unit,the sealing cage,together with the thrust retaining ring form an efficient gap sealing.Very heavy load can be used on this yoke type track rollers.Even with very high speed,it can bear impact axle load due to its axle guidance of its rolling bodies.


    Tolerance

    In common cases,the precision of the dimensions,shape and the rotation of this yoke type track roller is P0 grade.The outer diameter tolerance of the yoke type track roller with an arc outer diameter is 0£ˉ-0.05mm,the width tolerance of NATR,NATV,NUTR bearings is h12.


    Center adjustability

    The yoke type track roller with diameter of cylindrical shape have very small center adjustability.With low load,the center adjustability is 3-4'which with middle and heavy load,it is 5-7'.The yoke type track with diameter of arc shape have a center adjustability of 15-20'.For bigger angle variation,the edge effect will increase with the different loads.This will decrease the life of the bearing.



    curve roller is composed of a stud used as the tray of a group of rollers and a thick wall outer ring .The shoulder of the stud and the surface retaining ring on the stud form the guiding faces on the two sides of the outer ring.When the curve rollers are running on the plain tray or cam wheel,the inner stress on the rollers will increase due to the deformation of the outer ring.Therefore the rated load should be selected as curve roller column in this operational case.

    Structure

    KR
    Curve rollers radically guided by the retaining edge and ring

    KR - PP
    Curve rollers with sealing ring

    KRE
    Curve rollers with eccentric sleeve

    KRE - PP
    Curve rollers with eccentric sleeve and retaining sleeve

    KRV
    Curve rollers radically guided by the retaining edge and ring,Full complement needle roller type

    KRV - PP
    Curve rollers with sealing ring

    KRVE
    Curve rollers with eccentric sleeve

    KRVE - PP
    Curve rollers with eccentric sleeve and retaining sleeve

    NUKR
    Curve rollers axile guided by rolling bodies,full roller type

    NUKRE
    Curve rollers with eccentric sleeve

    CR
    Inch series curve rollers


    KR and KR...PP type curve rollers

    In KR,KR...PP curve rollers,the rolling needles are guided by the retainer while the outer ring is guided by the retaining ring shaft on the stud.These rollers are suitable for heave load and middle speed revolution.The lubricating can last a long period due to the bigger grease storage space inside the bearing.KR...PP curve roller is of contacting sealing structure.The operational temperature is -30??-100??.


    KR and KR...PP type curve rollers

    KRV,KRV...PP curve rollers have the same structures as KR,KR...PP type but they are filled with needle bearings.They can be used to bear heavier load and run with lower speed.They should be lubricated very often.


    NUKR type curve rollers

    This series curve rollers are of double lines full-roller structure.Like all cylindrical roller bearings,they are composed of outer ring cages pressed in the rolling bodies axle guidance and the retaining edge steps which forms highly effective gap sealing.

    Especially heavy load can be borne by these rollers and also they can sustain the axile load impact due to the axile guidance by the rollers.


    KRE,KRE...PP,KREV,KREV...PP,NUKRE type curve rollers

    Curve rollers of all these types can be supplied with eccentric sleeve.The rollers can be adjusted by adjusting the stud end face.The top of the eccentric sleeve is situated at the place where HSB is marked.Lubricating grease can be made through the both ends of the stud.

    NNTR

    NNTR 38110-2LS, ,NNTR 50130-2LS ,NNTR 50140-2LS ,NNTR 55140-2LS ,NNTR 60130-2LS ,NNTR 60150-2LS ,NNTR 60160-2LS ,NNTR 60165-2LS ,NNTR 65150-2LS ,NNTR 65160-2LS ,NNTR 70180-2LS ,NNTR 70190-2LS ,NNTR 80200-2LS ,NNTR 80210-2LS ,NNTR 80230-2LS ,NNTR 90220-2LS ,NNTR 90240-2LS ,NNTR 100210-2LS ,NNTR 100215-2LS ,NNTR 100240-2LS


     

     

    Copyright 2004-2017 Changzhou Enke Bearing Co.,Ltd
    一级做a爱过程免费视频曰_免费A级毛片无码久久版_久艾草久久综合精品无码国产AV_亚洲国产AⅤ精品一区二区11
  • <u id="cioag"></u>